Technical Material Guide: The Difference Between Solid and Coolant-Hole Carbide Blanks
- Share
- publisher
- Bree
- Issue Time
- Nov 5,2026
Summary
This technical material guide compares solid carbide blanks and coolant-hole carbide blanks, covering raw material rules, processing features, cost calculation and application scenarios for deep-hole drills and coolant tools.
Full Article Structure
- 1. Introduction: Two Main Types of Carbide Round Blanks
- 2. What Is Solid Carbide Blank & Coolant-Hole Blank
- 3. Side-by-Side Comparison: Solid vs Coolant-Hole Carbide Blank
- 4. Manufacturing & Cost Calculation Rules for Coolant Hole Rods
- 5. Application Suggestion For Choosing The Right Blank
- 6. FAQs About Coolant Hole Carbide Blanks
- 7. Summary: Match Blank Type With Your Cooling Requirement
1. Introduction: Two Main Types of Carbide Round Blanks
When ordering carbide round rods for drill and end mill production, you will choose between solid carbide blanks and coolant-hole carbide blanks. Many buyers are confused about their material difference, strength and pricing rules. This technical material guide clarifies the key differences and helps you pick the correct blank for your cutting tools.
2. What Is Solid Carbide Blank & Coolant-Hole Blank
- Solid carbide blank: fully dense WC-Co cylinder without any internal channel, uniform cross-section, the most common carbide rod blank
- Coolant-hole carbide blank: pre-formed internal straight or spiral coolant channels inside the carbide rod, designed for through coolant delivery to cutting edge
3. Side-by-Side Comparison: Solid vs Coolant-Hole Carbide Blank
| Item | Solid Carbide Blank | Coolant-Hole Carbide Blank |
|---|---|---|
| Internal structure | No internal hole | 1 hole / 2 holes / spiral holes |
| Structural strength | Higher bending strength, good for heavy cutting | Reduced strength, weakened by inner channels |
| Cooling performance | Relies only on external flood coolant | Direct coolant to cutting edge, excellent heat removal |
| Manufacturing difficulty | Low, standard pressing and sintering | High, special mould and forming process |
| Unit price | Lower, stable cost | Much higher, depends on hole pattern and tolerance |
| Typical finished tool | End mills, engraving cutters, short drills | Deep hole drills, high performance coolant drills |
4. Manufacturing & Cost Calculation Rules for Coolant Hole Rods
Coolant-hole carbide rods are not machined by drilling holes after sintering. The internal channels are formed during powder compaction before sintering. Post-sinter drilling of carbide is extremely hard and risky, so we use dedicated forming pins in the pressing mould.
Cost factors for coolant hole blanks:
- Number of holes: double holes cost more than single straight hole
- Hole tolerance: tighter tolerance raises reject rate
- Spiral coolant hole: the most complex and highest cost type
- Rod diameter: small diameter rods with coolant holes have very high scrap rate
5. Application Suggestion For Choosing The Right Blank
Choose solid carbide blanks if you make standard end mills, engraving tools, short drills and inserts. They are stronger, cheaper and easier to grind. Solid rods are the best choice when your cutting depth is shallow and external coolant is enough.
Select coolant-hole carbide blanks mainly for deep hole drilling. When the depth-to-diameter ratio is over 3xD, external coolant cannot reach the cutting tip effectively. Internal coolant holes push lubricant directly to the cutting zone, reduce built-up edge and extend tool life significantly. But you need to accept the lower bending strength and higher cost.
6. FAQs About Coolant Hole Carbide Blanks
Q1: Can we drill coolant holes on sintered solid carbide rods?
It is technically possible but not recommended. It is slow, expensive and easy to create microcracks inside the carbide, which will cause early tool breakage.
Q2: Does coolant hole design change the carbide grade?
The WC-Co grade formula stays the same. The grade only controls hardness and toughness; the hole layout is just a structural design.
Q3: Are spiral coolant holes better than straight holes?
Spiral holes deliver smoother coolant flow and better structural balance, but they have longer lead time and higher price.
7. Summary: Match Blank Type With Your Cooling Requirement
Solid carbide blanks remain the mainstream for most general cutting tools. Coolant-hole carbide blanks are a specialized solution focused on deep-hole cooling. Before ordering, confirm your drill depth, coolant pressure and budget. Our team can recommend straight or spiral coolant hole layout according to your finished drill drawing.
CTA Contact Zone
Check Coolant Hole Quotation
📧 Contact Us → /contact-us.htm
Send your drawing with hole size, position and tolerance for formal quotation.
Confirm Feasibility
📧 Contact Us → /contact-us.htm
We evaluate whether your small diameter rod can be made with internal coolant channels.
Disclaimer
Strength reduction of coolant-hole blanks varies by diameter and hole layout. Sample testing before mass production is highly recommended for critical drilling tools.